Patching Drywall Holes – How To Get Started

Let’s all admit it. Plastering walls has never been easy, since it requires a lot of time to dry it all out. Good thing we no longer have to use it since drywall is easier to install and handle. Though it can only withstand limited abuse, as long as you secure them to the joists, it shouldn’t be that much of a problem.

For a successful drywall repair, you will need the following tools and materials:

-Steel square

-Utility knife

-Drywall saw

-Taping knives

-Scrap wood

-Drywall screws or nails

-Fiberglass mesh tape

-Joint compound

-Sanding block

Using the steel square, measure and outline the damaged area, extending an inch or so on all sides around the hole. Make sure the sides have studs behind it to support the panel securely. This is important since working with an irregularly-shaped hole can take a lot of time.

Reach inside the hole if there are any obstructions behind the panel. To remove the damaged area, use a utility knife to run it over the lines. You may have to repeat this step until the drywall is completely detached. Do not forget to remove the torn paper edges before you proceed.

Use a scrap wood as a support for the new drywall patch. Cut it a bit longer then the opening and attach them with drywall screws. Make sure the nail heads are below the surface to avoid applying multiple layers of compound when finishing the panel.

You can now attach the panel inside the hole and drill the screws to the joists. To prevent the drywall from crumbling, do not screw nails near the edges. When drilling, make sure not to screw the nails too deep.

Seal the gap in between by taping all the seams with a mesh tape. To prevent having a bubbled tape effect, press the fiberglass tape evenly and smooth it out on the edges. Use a spackling compound to cover the tape pieces and let it dry. Once dry, cover the entire panel with spackling compound and feather out the edges. Leave it for a couple of hours and sand the panel lightly to remove the bumps and beads.

Simple isn’t it? Knowing how to patch should be easy as long as you’re willing to get your hands dirty. However, feel free to contact a specialist for professional help.

Learn more about drywall repair Louisville . Stop by Brian Winters site where you can find out all about drywall repair Louisville KY and how it can benefit you.

Patching Drywall Holes – How To Get Started



via downshar http://www.downshar.com/?p=1875

read more

Beginner’s Guide To Seamless Drywall Repair

Drywall is not the most durable material for covering walls and ceilings. That is why repairing drywall is an inevitable task for every homeowner. To master this skill like an expert, a lot of practice and patience are necessary. Achieve a flawless and seamless drywall repair by following the tips listed below.

With a sharp razor knife, remove the damaged panel by cutting a square around the hole. Do not follow the shape of the hole since this can be difficult to repair in the process. Remove the torn edges around the hole to make it easy to flush the panel.

Use a backer board for added support and slip it inside the hole. This will serve as a surface to anchor the new drywall panel. If the backer board doesn’t fit, you can enlarge the hole a bit more. You may need to attach a screw to the board for you to have something to hold on while you install the backer board.

Install the backer board by countersinking the screws on the corners. Measure the hole and cut a piece of drywall to fit it inside the damaged area. You can use drywall screws to attach it to the backer board. Make sure the nail heads are below the surface to avoid applying multiple layers of joint compound.

For beginners, it is best to use mesh tapes since they are easier to use than paper tapes. Conceal the seams with the mesh tape and apply a layer of drywall mud to cover the tape pieces. Use a taping knife to squeeze the excess compound and eliminate air pockets at the same time.

There is no need to apply a second coating if the panel is already flushed with your existing drywall. For beginners, apply another layer of drywall mud as a finishing coat and lightly sand the surface area. This is important if you want to achieve a seamless repair.

Once the top coat has dried, remove the remaining imperfections by lightly sanding the area for the second time. Apply primer once the surface is smooth and even. Do not take this lightly since primer prevents the compound from drying up the paint. Use a paint roller to make it easier to texturize the drywall panel.

At this point, the hole should already be covered up, as if nothing happened. However, do not hesitate to contact a specialist if you are uncomfortable in carrying out repairs on your own. Observe how the experts do it to learn a few tips and tricks to achieve a successful drywall repair.

Want to find out more about drywall repair Santa Ana , then visit Lori Philipps site to get advice on proper drywall repair Santa Ana CA.

Beginner’s Guide To Seamless Drywall Repair



via downshar http://www.downshar.com/?p=1747

read more

Drywall Hole Repair – What To Do

Drywall is widely used by the construction industry for covering walls and ceilings even though it is not the strongest material compared to wood laths and plaster. Typically, drywall is made of plaster or wood pulp that is pressed between thick sheets of paper. Take action as soon as your drywall breaks to avoid further damage.

Avoid encountering unnecessary disasters by wearing protective glasses, gloves and footwear when repairing drywall. No matter how small the repair is, it doesn’t hurt to take safety precautions beforehand. For large-scale repairs, secure the area and do not let anyone in your household enter the room until the repair is finished.

Gather all the tools and materials needed before proceeding. Avoid having drywall flaps by removing the torn edges with a utility knife. For larger holes, cut a square-sized panel to remove the hole and repair the damaged area. Wipe the panel with trisodium phosphate to strengthen its adhesion. Just be careful not to wet the drywall too much to avoid further damage.

Cover the hole with the patch and taped its edges. It is best to use drywall screws to attach the panel if the hole is larger than the usual. If you’re a beginner, use fiberglass mesh tapes to cover the seam since they adhere to the wall without using drywall mud. Paper tapes are usually used for concealing joints and require a thin coat of compound to make it stick. Smooth the surface area with a taping knife while squeezing the excess mud under the tape.

With a wide-blade putty knife, apply a layer of joint compound over the seam and spread it evenly. You may have a bumpy, rough and unnatural drywall if you put a thick layer of compound. Before adding a new coating, let it dry for a couple of hours.

Swipe your putty knife clean if you are having hard time spreading the compound evenly. Use a drywall sandpaper to sand the surface and remove the remaining imperfections. Once you are satisfied with the surface area, flush the panel with your existing drywall with a thin layer of finishing compound.

Apply at least two coats of primer before painting the drywall. This is important since a joint compound can dry up the paint easily. If you are using paint spray cans, do not hold the nozzle to close too the wall. You can also use paint rollers instead of brushes to avoid having brush marks on your drywall.

If you are not confident enough in fixing your drywall, call your local specialists to handle your drywall concerns in no time. These experts know how to patch a hole in drywall professionally, bring you guaranteed results like no other.

Learn more about drywall repair Huntington Beach . Stop by Brian Winters’s site where you can find out all about drywall repair Huntington Beach CA and how it can benefit you.

Drywall Hole Repair – What To Do



via downshar http://www.downshar.com/?p=1654

read more